Friday, March 16, 2018

Fabergé-Inspired Eggs for Easter

Decorative eggs made with epoxy resin clay and Swarovski resin crystals
Make a set of decorative eggs that not only represents their importance as symbols of new life for Easter but that can also be displayed throughout the year as a decor item in their own right. These jewelled eggs are inspired by the opulent Faberge eggs commissioned by the Russian Tsars. In place of the precious metal, enamel and jewels, these are made with EasySculpt epoxy resin clay and sparkly Swarovski crystals. This project also appeared in the Spring 2016 issue of Crafts Ideas Magazine.

Shopping List:

EnviroTex EasySculpt Epoxy Resin Clay
Colourants: Castin'Craft Resin Pigments and alcohol inks
2" polystyrene eggs
Embellie Gellie or Krystal Katana
2 x Swarovski flatback rivoli 2006 in colour of your choice
Swarovski flatback crystals SS8 in colours of your choice
G-S Hypo Cement
Talcum powder
Tissues and Methylated Spirits (denatured alcohol) or baby wipes
Teflon craft sheet
Gloves

Tools: clay blade, needle tool, timer,


How to Make Decorative Resin Clay Eggs

Tip: Before beginning to work with EasySculpt, put on a pair of close fitting gloves because resin clay is quite sticky when it's first mixed. It will be helpful to dust your gloves whenever the clay begins to stick to them.


Cover the Egg

Measure out and mix together equal parts of EasySculpt Clay following the manufacturer’s instructions. Set a timer for 25 minutes and leave the mixed clay to firm up because initially, it will be too sticky and stretchy to cover the egg.

Dust your gloves with powder and then flatten the clay into a circle. Place the center of the circle over the top of the egg. Work the clay down towards the bottom of the egg. Smooth out any folds that form and try to keep the clay an even thickness all the way around. Smooth out all the creases. There will probably be some pockets of air trapped under the clay. These can be pierced with the toothpick or needle tool. Smooth the clay with your finger until the hole disappears. Dust the Teflon sheet with a light sprinkling of powder. Balance the egg upright on the sheet and set the timer to 30 minutes. The clay will continue to firm up during this time.


The clay will still be quite soft and because it has some stretch in it, wrinkles will form in the bottom section of the egg. Use your gloved hand to smooth out the clay and set it aside. Set the timer for 10 minutes and then smooth again. Repeat again at 10 minute intervals until the egg is smooth. Roll the egg in your palms to give it a smooth all over finish.

Decorate the Egg


Apply a small amount of GS-Hypo Cement to the middle of the egg and attach a flat back Rivoli. Adhere another Rivoli on the opposite side of the egg in a slightly lower position.
Epoxy clay egg with Heliotrope Swarovski flatback rivoli.

Mix a small amount of EasySculpt. Roll it into three different sized balls. 
Different sized balls of mixed epoxy resin clay

Flatten one piece into a circle and add 2 drops of your choice of colour to the clay. Mix it in well. This will make the clay sticky and soft so powder your gloves as needed whilst you work the colour in. Clean your gloves with rubbing alcohol and a tissue to remove any residue. 
Epoxy Resin Clay being coloured with purple alcohol ink

Colour the other two balls with the other colourants you’ve chosen. Set the timer for 10 minutes to allow the clay to firm up a little before continuing. 
Note: You will notice that some of the alcohol ink colours will fade as they cure.
Balls of epoxy resin clay coloured with alcohol inks

Dust the Teflon sheet lightly with powder. Pull a small amount from one ball of clay and roll it on the sheet to form a snake 3mm (1/8”) thick and approximately 11.5cm (4 ½”) long.
Thin log of epoxy resin clay

Begin coiling the clay around the rivoli and then create an “S” curve down the side of the egg, finishing in an open circle. 
Epoxy resin clay coiled in a "S" shape around a Swarovski crystal on a clay covered egg

Make additional coils in the other colours and place them alongside the first coil, following the same curve. Create another “S” curves around the other rivoli.
Two colours of epoxy resin clay coiled around a Swarovski crystal in an "S" shape

Form a piece of clay into a small log about ¼” wide. Cut it into pieces 6mm (¼”) long.
Epoxy resin clay log being cut into small blocks

Cut some of these pieces in halves, some into quarters and some into smaller pieces.
Epoxy resin clay cut into small chunks

Roll each one into a ball so that you have a variety of graduating sizes. Set these aside to firm up.
Coloured epoxy resin clay rolled into graduating sized balls

Roll out another ¼” wide log and cut it into 6mm (¼”) lengths. Roll each into a ball and then taper one end to form a teardrop shape. Press the tip of the needle tool into the middle of each teardrop.

Coloured epoxy resin clay being formed into teardrop shapes
Teardrop shaped pieces of purple epoxy resin clay with an indentation down the centre.

Position these at an angle around the outside curves of the coils with the points facing in. Use adhesive to secure them if they have begun to cure. On some coils, attach graduating sized balls along the curve with the adhesive.


Epoxy resin clay teardrops along a coloured resin clay swirl

Position crystals along the middle coil in some of the “S” curves. If the clay is no longer sticky, use G-S Hypo Cement to attach them.
Epoxy resin clay covered egg being decorated with Swarovski crystals

Now that you've finished your decorative Easter egg, make a few in different colour combinations. They look stunning displayed in ornate egg stands. Or place them in a bowl on your coffee table and admire them all year 'round.

Like this project? Pin it for later.
Faberge inspired eggs covered with epoxy resin clay and decorated with Swarovski crystals

Happy Resining!


Subscribe to my email list and learn how to resin like an expert.


Would you like to comment?

Thanks for stopping by today. Your comment is really appreciated.